野火RA6M5开发板 IIC-OLED测试学习

delehub

野火RA6M5开发板 IIC-OLED测试学习

野火RA6M5开发板,这里我使用的时SCI模块里面的SCL5 SDA5 ，配置引脚为P805,P513，配置的过程主要是在官方的e2studio去配置的，简单的点几下就可以了

具体参考下面的博客

\

野火RA6M5开发板上的外部高速晶振为24M.

由于我的jlink版本不支持Cortex-M33内核的芯片下载，现在只能通过Uart串口烧写，开发文档上面也有具体的操作
瑞萨开发板通过Uart串口烧写程序参考博文 https://bbs.elecfans.com/jishu_2322246_1_1.html

IIC配置 参考文章 瑞萨e2studio-IIC-12864OLED移植 https://blog.csdn.net/qq_24312945/article/details/121373564

野火RA6M5开发板,这里我使用的时SCI模块里面的SCL5 SDA5 ，配置引脚为P805,P513

1. //==================================================================================================
   
2. //  实现功能: 0.96寸OLED 接口演示例程
   
3. //  说明:
   
4. //              GND   电源地
   
5. //              VCC   接5V或3.3v电源
   
6. //              SCL   接P513（SCL5）
   
7. //              SDA   接P805（SDA5）
   
8. //==================================================================================================------------------------------------------------------------------------
   
9. //  |   -   |   -   |   0   |   1   |   2   |   3   |   4   |   5   |   6   |   7   |   8   |   9
   
10. //==================================================================================================
    
11. //==================================================================================================
    
12. #include "oled.h"
    
13. #include "stdlib.h"
    
14. #include "oledfont.h"
    
15. #include "math.h"
    
16. #include "hal_data.h"
    
17. 
    
18. 
    
19. extern fsp_err_t err;
    
20. extern int  timeout_ms;
    
21. extern  i2c_master_event_t i2c_event ;
    
22. //OLED的显存
    
23. //存放格式如下.
    
24. //[0]0 1 2 3 ... 127
    
25. //[1]0 1 2 3 ... 127
    
26. //[2]0 1 2 3 ... 127
    
27. //[3]0 1 2 3 ... 127
    
28. //[4]0 1 2 3 ... 127
    
29. //[5]0 1 2 3 ... 127
    
30. //[6]0 1 2 3 ... 127
    
31. //[7]0 1 2 3 ... 127
    
32. 
    
33. //==================================================================================================
    
34. //  函数功能: IIC外设驱动函数部分
    
35. //  函数标记: Write_IIC_Command
    
36. //  函数说明: 无
    
37. //-------------------------------------------------------------------------------------------------
    
38. //  |   -   |   -   |   0   |   1   |   2   |   3   |   4   |   5   |   6   |   7   |   8   |   9
    
39. //==================================================================================================
    
40. void Write_IIC_Command(unsigned char IIC_Command)
    
41. {
    
42. 
    
43.     uint8_t ii[2]={0x00,0x00};
    
44.     ii[1] = IIC_Command;
    
45. 
    
46.     err = R_SCI_I2C_Write(&g_i2c5_ctrl, ii, 0x02, true);
    
47.     assert(FSP_SUCCESS == err);
    
48.     /* Since there is nothing else to do, block until Callback triggers*/
    
49.     //while ((I2C_MASTER_EVENT_TX_COMPLETE != i2c_event) && timeout_ms)
    
50.     while ((I2C_MASTER_EVENT_TX_COMPLETE != i2c_event) && timeout_ms>0)
    
51.     {
    
52.         R_BSP_SoftwareDelay(100U, BSP_DELAY_UNITS_MICROSECONDS);
    
53.         timeout_ms--;
    
54.     }
    
55.     if (I2C_MASTER_EVENT_ABORTED == i2c_event)
    
56.     {
    
57.         __BKPT(0);
    
58.     }
    
59.     /* Read data back from the I2C slave */
    
60.     i2c_event = I2C_MASTER_EVENT_ABORTED;
    
61.     timeout_ms           = 100000;
    
62. }
    
63. 
    
64. //==================================================================================================
    
65. //  函数功能: IIC外设驱动函数部分
    
66. //  函数标记: Write_IIC_Data
    
67. //  函数说明: 无
    
68. //-------------------------------------------------------------------------------------------------
    
69. //  |   -   |   -   |   0   |   1   |   2   |   3   |   4   |   5   |   6   |   7   |   8   |   9
    
70. //==================================================================================================
    
71. void Write_IIC_Data(unsigned char IIC_Data)
    
72. {
    
73.     uint8_t ii[2]={0x40,0x00};
    
74.     ii[0] = 0x40;
    
75.     ii[1] = IIC_Data;
    
76.     err = R_SCI_I2C_Write(&g_i2c5_ctrl, ii, 0x02, true);
    
77.            assert(FSP_SUCCESS == err);
    
78.            /* Since there is nothing else to do, block until Callback triggers*/
    
79.            //while ((I2C_MASTER_EVENT_TX_COMPLETE != i2c_event) && timeout_ms)
    
80.     while ((I2C_MASTER_EVENT_TX_COMPLETE != i2c_event) && timeout_ms>0)
    
81.     {
    
82.         R_BSP_SoftwareDelay(100U, BSP_DELAY_UNITS_MICROSECONDS);
    
83.         timeout_ms--;
    
84.     }
    
85.     if (I2C_MASTER_EVENT_ABORTED == i2c_event)
    
86.     {
    
87.         __BKPT(0);
    
88.     }
    
89.     /* Read data back from the I2C slave */
    
90.     i2c_event = I2C_MASTER_EVENT_ABORTED;
    
91.     timeout_ms           = 100000;
    
92. 
    
93. }
    
94. //==================================================================================================
    
95. //  函数功能: IIC外设驱动函数部分
    
96. //  函数标记: Write_IIC_Data
    
97. //  函数说明: 无
    
98. //-------------------------------------------------------------------------------------------------
    
99. //  |   -   |   -   |   0   |   1   |   2   |   3   |   4   |   5   |   6   |   7   |   8   |   9
    
100. //==================================================================================================
     
101. void OLED_WR_Byte(unsigned dat,unsigned cmd)
     
102. {
     
103.     if(cmd)
     
104.     {
     
105.         Write_IIC_Data(dat);
     
106.     }
     
107.     else
     
108.     {
     
109.         Write_IIC_Command(dat);
     
110.     }
     
111. 
     
112. 
     
113. }
     
114. /********************************************
     
115. // fill_Picture
     
116. ********************************************/
     
117. void fill_picture(unsigned char fill_Data)
     
118. {
     
119.     unsigned char m,n;
     
120.     for(m=0;m<8;m++)
     
121.     {
     
122.         OLED_WR_Byte(0xb0+m,0);     //page0-page1
     
123.         OLED_WR_Byte(0x00,0);       //low column start address
     
124.         OLED_WR_Byte(0x10,0);       //high column start address
     
125.         for(n=0;n<128;n++)
     
126.             {
     
127.                 OLED_WR_Byte(fill_Data,1);
     
128.             }
     
129.     }
     
130. }
     
131. 
     
132. 
     
133. /***********************Delay****************************************/
     
134. void Delay_50ms(unsigned int Del_50ms)
     
135. {
     
136.     unsigned int m;
     
137.     for(;Del_50ms>0;Del_50ms--)
     
138.         for(m=6245;m>0;m--);
     
139. }
     
140. 
     
141. void Delay_1ms(unsigned int Del_1ms)
     
142. {
     
143.     unsigned char j;
     
144.     while(Del_1ms--)
     
145.     {
     
146.         for(j=0;j<123;j++);
     
147.     }
     
148. }
     
149. 
     
150. //坐标设置
     
151. 
     
152. void OLED_Set_Pos(unsigned char x, unsigned char y)
     
153. {   OLED_WR_Byte(0xb0+y,OLED_CMD);
     
154.     OLED_WR_Byte(((x&0xf0)>>4)|0x10,OLED_CMD);
     
155.     OLED_WR_Byte((x&0x0f),OLED_CMD);
     
156. }
     
157. //开启OLED显示
     
158. void OLED_Display_On(void)
     
159. {
     
160.     OLED_WR_Byte(0X8D,OLED_CMD);  //SET DCDC命令
     
161.     OLED_WR_Byte(0X14,OLED_CMD);  //DCDC ON
     
162.     OLED_WR_Byte(0XAF,OLED_CMD);  //DISPLAY ON
     
163. }
     
164. //关闭OLED显示
     
165. void OLED_Display_Off(void)
     
166. {
     
167.     OLED_WR_Byte(0X8D,OLED_CMD);  //SET DCDC命令
     
168.     OLED_WR_Byte(0X10,OLED_CMD);  //DCDC OFF
     
169.     OLED_WR_Byte(0XAE,OLED_CMD);  //DISPLAY OFF
     
170. }
     
171. //清屏函数,清完屏,整个屏幕是黑色的!和没点亮一样!!!
     
172. void OLED_Clear(void)
     
173. {
     
174.     u8 i,n;
     
175.     for(i=0;i<8;i++)
     
176.     {
     
177.         OLED_WR_Byte(0xb0+i,OLED_CMD);    //设置页地址（0~7）
     
178.         OLED_WR_Byte(0x00,OLED_CMD);      //设置显示位置—列低地址
     
179.         OLED_WR_Byte(0x10,OLED_CMD);      //设置显示位置—列高地址
     
180.         for(n=0;n<128;n++)OLED_WR_Byte(0,OLED_DATA);
     
181.     } //更新显示
     
182. }
     
183. void OLED_On(void)
     
184. {
     
185.     u8 i,n;
     
186.     for(i=0;i<8;i++)
     
187.     {
     
188.         OLED_WR_Byte (0xb0+i,OLED_CMD);    //设置页地址（0~7）
     
189.         OLED_WR_Byte (0x00,OLED_CMD);      //设置显示位置—列低地址
     
190.         OLED_WR_Byte (0x10,OLED_CMD);      //设置显示位置—列高地址
     
191.         for(n=0;n<128;n++)OLED_WR_Byte(1,OLED_DATA);
     
192.     } //更新显示
     
193. }
     
194. //在指定位置显示一个字符,包括部分字符
     
195. //x:0~127
     
196. //y:0~63
     
197. //mode:0,反白显示;1,正常显示
     
198. //size:选择字体 16/12
     
199. void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 Char_Size)
     
200. {
     
201.     unsigned char c=0,i=0;
     
202.         c=chr-' ';//得到偏移后的值
     
203.         if(x>Max_Column-1){x=0;y=y+2;}
     
204.         if(Char_Size ==16)
     
205.             {
     
206.                 OLED_Set_Pos(x,y);
     
207.                 for(i=0;i<8;i++)
     
208.                     OLED_WR_Byte(F8X16[c*16+i],OLED_DATA);
     
209.                     OLED_Set_Pos(x,y+1);
     
210.                     for(i=0;i<8;i++)
     
211.                         OLED_WR_Byte(F8X16[c*16+i+8],OLED_DATA);
     
212.             }
     
213.             else {
     
214.                 OLED_Set_Pos(x,y);
     
215.                 for(i=0;i<6;i++)
     
216.                 OLED_WR_Byte(F6x8[c][i],OLED_DATA);
     
217. 
     
218.             }
     
219. }
     
220. //m^n函数
     
221. u32 oled_pow(u8 m,u8 n)
     
222. {
     
223.     u32 result=1;
     
224.     while(n--)result*=m;
     
225.     return result;
     
226. }
     
227. //显示2个数字
     
228. //x,y :起点坐标
     
229. //len :数字的位数
     
230. //size:字体大小
     
231. //mode:模式   0,填充模式;1,叠加模式
     
232. //num:数值(0~4294967295);
     
233. void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size2)
     
234. {
     
235.     u8 t,temp;
     
236.     u8 enshow=0;
     
237.     for(t=0;t<len;t++)
     
238.     {
     
239.         temp=(num/oled_pow(10,len-t-1))%10;
     
240.         if(enshow==0&&t<(len-1))
     
241.         {
     
242.             if(temp==0)
     
243.             {
     
244.                 OLED_ShowChar(x+(size2/2)*t,y,' ',size2);
     
245.                 continue;
     
246.             }else enshow=1;
     
247. 
     
248.         }
     
249.         OLED_ShowChar(x+(size2/2)*t,y,temp+'0',size2);
     
250.     }
     
251. }
     
252. //显示一个字符号串
     
253. void OLED_ShowString(u8 x,u8 y,u8 *chr,u8 Char_Size)
     
254. {
     
255.     unsigned char j=0;
     
256.     while (chr[j]!='\0')
     
257.     {       OLED_ShowChar(x,y,chr[j],Char_Size);
     
258.             x+=8;
     
259.         if(x>120){x=0;y+=2;}
     
260.             j++;
     
261.     }
     
262. }
     
263. //显示汉字
     
264. void OLED_ShowCHinese(u8 x,u8 y,u8 no)
     
265. {
     
266.     u8 t,adder=0;
     
267.     OLED_Set_Pos(x,y);
     
268.     for(t=0;t<16;t++)
     
269.         {
     
270.                 OLED_WR_Byte(Hzk[2*no][t],OLED_DATA);
     
271.                 adder+=1;
     
272.      }
     
273.         OLED_Set_Pos(x,y+1);
     
274.     for(t=0;t<16;t++)
     
275.             {
     
276.                 OLED_WR_Byte(Hzk[2*no+1][t],OLED_DATA);
     
277.                 adder+=1;
     
278.       }
     
279. }
     
280. /***********功能描述：显示显示BMP图片128×64起始点坐标(x,y),x的范围0～127，y为页的范围0～7*****************/
     
281. void OLED_DrawBMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[])
     
282. {
     
283. unsigned int j=0;
     
284. unsigned char x,y;
     
285. 
     
286.   if(y1%8==0) y=y1/8;
     
287.   else y=y1/8+1;
     
288.     for(y=y0;y<y1;y++)
     
289.     {
     
290.         OLED_Set_Pos(x0,y);
     
291.     for(x=x0;x<x1;x++)
     
292.         {
     
293.             OLED_WR_Byte(BMP[j++],OLED_DATA);
     
294.         }
     
295.     }
     
296. }
     
297. 
     
298. //初始化SSD1306
     
299. void OLED_Init(void)
     
300. {
     
301. 
     
302. //    GPIO_InitTypeDef  GPIO_InitStructure;
     
303. //
     
304. //
     
305. //    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);    //使能A端口时钟
     
306. //    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5|GPIO_Pin_7;
     
307. //    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;         //推挽输出
     
308. //    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//速度50MHz
     
309. //    GPIO_Init(GPIOA, &GPIO_InitStructure);    //初始化GPIOD3,6
     
310. //    GPIO_SetBits(GPIOA,GPIO_Pin_5|GPIO_Pin_7);
     
311. 
     
312. 
     
313. //delay_ms(800);
     
314. 
     
315. 
     
316.     /* Wait for minimum time required between transfers. */
     
317.     R_BSP_SoftwareDelay(800, BSP_DELAY_UNITS_MICROSECONDS);
     
318. 
     
319. OLED_WR_Byte(0xAE,OLED_CMD);//--display off
     
320.     OLED_WR_Byte(0x00,OLED_CMD);//---set low column address
     
321.     OLED_WR_Byte(0x10,OLED_CMD);//---set high column address
     
322.     OLED_WR_Byte(0x40,OLED_CMD);//--set start line address
     
323.     OLED_WR_Byte(0xB0,OLED_CMD);//--set page address
     
324.     OLED_WR_Byte(0x81,OLED_CMD); // contract control
     
325.     OLED_WR_Byte(0xFF,OLED_CMD);//--128
     
326.     OLED_WR_Byte(0xA1,OLED_CMD);//set segment remap
     
327.     OLED_WR_Byte(0xA6,OLED_CMD);//--normal / reverse
     
328.     OLED_WR_Byte(0xA8,OLED_CMD);//--set multiplex ratio(1 to 64)
     
329.     OLED_WR_Byte(0x3F,OLED_CMD);//--1/32 duty
     
330.     OLED_WR_Byte(0xC8,OLED_CMD);//Com scan direction
     
331.     OLED_WR_Byte(0xD3,OLED_CMD);//-set display offset
     
332.     OLED_WR_Byte(0x00,OLED_CMD);//
     
333. 
     
334.     OLED_WR_Byte(0xD5,OLED_CMD);//set osc division
     
335.     OLED_WR_Byte(0x80,OLED_CMD);//
     
336. 
     
337.     OLED_WR_Byte(0xD8,OLED_CMD);//set area color mode off
     
338.     OLED_WR_Byte(0x05,OLED_CMD);//
     
339. 
     
340.     OLED_WR_Byte(0xD9,OLED_CMD);//Set Pre-Charge Period
     
341.     OLED_WR_Byte(0xF1,OLED_CMD);//
     
342. 
     
343.     OLED_WR_Byte(0xDA,OLED_CMD);//set com pin configuartion
     
344.     OLED_WR_Byte(0x12,OLED_CMD);//
     
345. 
     
346.     OLED_WR_Byte(0xDB,OLED_CMD);//set Vcomh
     
347.     OLED_WR_Byte(0x30,OLED_CMD);//
     
348. 
     
349.     OLED_WR_Byte(0x8D,OLED_CMD);//set charge pump enable
     
350.     OLED_WR_Byte(0x14,OLED_CMD);//
     
351. 
     
352.     OLED_WR_Byte(0xAF,OLED_CMD);//--turn on oled panel
     
353. }

复制代码

1. /*
   
2. * oled.h
   
3. *
   
4. *  Created on: 2023年1月31日
   
5. *      Author: a8456
   
6. */
   
7. 
   
8. #ifndef OLED_H_
   
9. #define OLED_H_
   
10. #include "stdlib.h"
    
11. #include "stdint.h"
    
12. #define OLED_MODE 0
    
13. 
    
14. #define XLevelL     0x00
    
15. #define XLevelH     0x10
    
16. #define Max_Column  128
    
17. #define Max_Row     64
    
18. #define Brightness  0xFF
    
19. #define X_WIDTH     128
    
20. #define Y_WIDTH     64
    
21. 
    
22. 
    
23. #define OLED_CMD  0 //写命令
    
24. #define OLED_DATA 1 //写数据
    
25. 
    
26. typedef __uint8_t u8 ;
    
27. typedef __uint32_t u32 ;
    
28. 
    
29. 
    
30. //OLED控制用函数
    
31. void OLED_WR_Byte(unsigned dat,unsigned cmd);
    
32. void OLED_Display_On(void);
    
33. void OLED_Display_Off(void);
    
34. void OLED_Init(void);
    
35. void OLED_Clear(void);
    
36. void OLED_DrawPoint(u8 x,u8 y,u8 t);
    
37. void OLED_Fill(u8 x1,u8 y1,u8 x2,u8 y2,u8 dot);
    
38. void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 Char_Size);
    
39. void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size);
    
40. void OLED_ShowString(u8 x,u8 y, u8 *p,u8 Char_Size);
    
41. void OLED_Set_Pos(unsigned char x, unsigned char y);
    
42. void OLED_ShowCHinese(u8 x,u8 y,u8 no);
    
43. void OLED_DrawBMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[]);
    
44. void Delay_50ms(unsigned int Del_50ms);
    
45. void Delay_1ms(unsigned int Del_1ms);
    
46. void fill_picture(unsigned char fill_Data);
    
47. void Picture();
    
48. void IIC_Start();
    
49. void IIC_Stop();
    
50. void Write_IIC_Command(unsigned char IIC_Command);
    
51. void Write_IIC_Data(unsigned char IIC_Data);
    
52. void Write_IIC_Byte(unsigned char IIC_Byte);
    
53. 
    
54. void IIC_Wait_Ack();
    
55. #endif /* OLED_H_ */

复制代码

1. /*
   
2. * oledfont.h
   
3. *
   
4. *  Created on: 2023年1月31日
   
5. *      Author: a8456
   
6. */
   
7. 
   
8. #ifndef OLEDFONT_H_
   
9. #define OLEDFONT_H_
   
10. 
    
11. //常用ASCII表
    
12. //偏移量32
    
13. //ASCII字符集
    
14. //偏移量32
    
15. //大小:12*6
    
16. /************************************6*8的点阵************************************/
    
17. const unsigned char F6x8[][6] =
    
18. {
    
19. 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,// sp
    
20. 0x00, 0x00, 0x00, 0x2f, 0x00, 0x00,// !
    
21. 0x00, 0x00, 0x07, 0x00, 0x07, 0x00,// "
    
22. 0x00, 0x14, 0x7f, 0x14, 0x7f, 0x14,// #
    
23. 0x00, 0x24, 0x2a, 0x7f, 0x2a, 0x12,// $
    
24. 0x00, 0x62, 0x64, 0x08, 0x13, 0x23,// %
    
25. 0x00, 0x36, 0x49, 0x55, 0x22, 0x50,// &
    
26. 0x00, 0x00, 0x05, 0x03, 0x00, 0x00,// '
    
27. 0x00, 0x00, 0x1c, 0x22, 0x41, 0x00,// (
    
28. 0x00, 0x00, 0x41, 0x22, 0x1c, 0x00,// )
    
29. 0x00, 0x14, 0x08, 0x3E, 0x08, 0x14,// *
    
30. 0x00, 0x08, 0x08, 0x3E, 0x08, 0x08,// +
    
31. 0x00, 0x00, 0x00, 0xA0, 0x60, 0x00,// ,
    
32. 0x00, 0x08, 0x08, 0x08, 0x08, 0x08,// -
    
33. 0x00, 0x00, 0x60, 0x60, 0x00, 0x00,// .
    
34. 0x00, 0x20, 0x10, 0x08, 0x04, 0x02,// /
    
35. 0x00, 0x3E, 0x51, 0x49, 0x45, 0x3E,// 0
    
36. 0x00, 0x00, 0x42, 0x7F, 0x40, 0x00,// 1
    
37. 0x00, 0x42, 0x61, 0x51, 0x49, 0x46,// 2
    
38. 0x00, 0x21, 0x41, 0x45, 0x4B, 0x31,// 3
    
39. 0x00, 0x18, 0x14, 0x12, 0x7F, 0x10,// 4
    
40. 0x00, 0x27, 0x45, 0x45, 0x45, 0x39,// 5
    
41. 0x00, 0x3C, 0x4A, 0x49, 0x49, 0x30,// 6
    
42. 0x00, 0x01, 0x71, 0x09, 0x05, 0x03,// 7
    
43. 0x00, 0x36, 0x49, 0x49, 0x49, 0x36,// 8
    
44. 0x00, 0x06, 0x49, 0x49, 0x29, 0x1E,// 9
    
45. 0x00, 0x00, 0x36, 0x36, 0x00, 0x00,// :
    
46. 0x00, 0x00, 0x56, 0x36, 0x00, 0x00,// ;
    
47. 0x00, 0x08, 0x14, 0x22, 0x41, 0x00,// <
    
48. 0x00, 0x14, 0x14, 0x14, 0x14, 0x14,// =
    
49. 0x00, 0x00, 0x41, 0x22, 0x14, 0x08,// >
    
50. 0x00, 0x02, 0x01, 0x51, 0x09, 0x06,// ?
    
51. 0x00, 0x32, 0x49, 0x59, 0x51, 0x3E,// @
    
52. 0x00, 0x7C, 0x12, 0x11, 0x12, 0x7C,// A
    
53. 0x00, 0x7F, 0x49, 0x49, 0x49, 0x36,// B
    
54. 0x00, 0x3E, 0x41, 0x41, 0x41, 0x22,// C
    
55. 0x00, 0x7F, 0x41, 0x41, 0x22, 0x1C,// D
    
56. 0x00, 0x7F, 0x49, 0x49, 0x49, 0x41,// E
    
57. 0x00, 0x7F, 0x09, 0x09, 0x09, 0x01,// F
    
58. 0x00, 0x3E, 0x41, 0x49, 0x49, 0x7A,// G
    
59. 0x00, 0x7F, 0x08, 0x08, 0x08, 0x7F,// H
    
60. 0x00, 0x00, 0x41, 0x7F, 0x41, 0x00,// I
    
61. 0x00, 0x20, 0x40, 0x41, 0x3F, 0x01,// J
    
62. 0x00, 0x7F, 0x08, 0x14, 0x22, 0x41,// K
    
63. 0x00, 0x7F, 0x40, 0x40, 0x40, 0x40,// L
    
64. 0x00, 0x7F, 0x02, 0x0C, 0x02, 0x7F,// M
    
65. 0x00, 0x7F, 0x04, 0x08, 0x10, 0x7F,// N
    
66. 0x00, 0x3E, 0x41, 0x41, 0x41, 0x3E,// O
    
67. 0x00, 0x7F, 0x09, 0x09, 0x09, 0x06,// P
    
68. 0x00, 0x3E, 0x41, 0x51, 0x21, 0x5E,// Q
    
69. 0x00, 0x7F, 0x09, 0x19, 0x29, 0x46,// R
    
70. 0x00, 0x46, 0x49, 0x49, 0x49, 0x31,// S
    
71. 0x00, 0x01, 0x01, 0x7F, 0x01, 0x01,// T
    
72. 0x00, 0x3F, 0x40, 0x40, 0x40, 0x3F,// U
    
73. 0x00, 0x1F, 0x20, 0x40, 0x20, 0x1F,// V
    
74. 0x00, 0x3F, 0x40, 0x38, 0x40, 0x3F,// W
    
75. 0x00, 0x63, 0x14, 0x08, 0x14, 0x63,// X
    
76. 0x00, 0x07, 0x08, 0x70, 0x08, 0x07,// Y
    
77. 0x00, 0x61, 0x51, 0x49, 0x45, 0x43,// Z
    
78. 0x00, 0x00, 0x7F, 0x41, 0x41, 0x00,// [
    
79. 0x00, 0x55, 0x2A, 0x55, 0x2A, 0x55,// 55
    
80. 0x00, 0x00, 0x41, 0x41, 0x7F, 0x00,// ]
    
81. 0x00, 0x04, 0x02, 0x01, 0x02, 0x04,// ^
    
82. 0x00, 0x40, 0x40, 0x40, 0x40, 0x40,// _
    
83. 0x00, 0x00, 0x01, 0x02, 0x04, 0x00,// '
    
84. 0x00, 0x20, 0x54, 0x54, 0x54, 0x78,// a
    
85. 0x00, 0x7F, 0x48, 0x44, 0x44, 0x38,// b
    
86. 0x00, 0x38, 0x44, 0x44, 0x44, 0x20,// c
    
87. 0x00, 0x38, 0x44, 0x44, 0x48, 0x7F,// d
    
88. 0x00, 0x38, 0x54, 0x54, 0x54, 0x18,// e
    
89. 0x00, 0x08, 0x7E, 0x09, 0x01, 0x02,// f
    
90. 0x00, 0x18, 0xA4, 0xA4, 0xA4, 0x7C,// g
    
91. 0x00, 0x7F, 0x08, 0x04, 0x04, 0x78,// h
    
92. 0x00, 0x00, 0x44, 0x7D, 0x40, 0x00,// i
    
93. 0x00, 0x40, 0x80, 0x84, 0x7D, 0x00,// j
    
94. 0x00, 0x7F, 0x10, 0x28, 0x44, 0x00,// k
    
95. 0x00, 0x00, 0x41, 0x7F, 0x40, 0x00,// l
    
96. 0x00, 0x7C, 0x04, 0x18, 0x04, 0x78,// m
    
97. 0x00, 0x7C, 0x08, 0x04, 0x04, 0x78,// n
    
98. 0x00, 0x38, 0x44, 0x44, 0x44, 0x38,// o
    
99. 0x00, 0xFC, 0x24, 0x24, 0x24, 0x18,// p
    
100. 0x00, 0x18, 0x24, 0x24, 0x18, 0xFC,// q
     
101. 0x00, 0x7C, 0x08, 0x04, 0x04, 0x08,// r
     
102. 0x00, 0x48, 0x54, 0x54, 0x54, 0x20,// s
     
103. 0x00, 0x04, 0x3F, 0x44, 0x40, 0x20,// t
     
104. 0x00, 0x3C, 0x40, 0x40, 0x20, 0x7C,// u
     
105. 0x00, 0x1C, 0x20, 0x40, 0x20, 0x1C,// v
     
106. 0x00, 0x3C, 0x40, 0x30, 0x40, 0x3C,// w
     
107. 0x00, 0x44, 0x28, 0x10, 0x28, 0x44,// x
     
108. 0x00, 0x1C, 0xA0, 0xA0, 0xA0, 0x7C,// y
     
109. 0x00, 0x44, 0x64, 0x54, 0x4C, 0x44,// z
     
110. 0x14, 0x14, 0x14, 0x14, 0x14, 0x14,// horiz lines
     
111. };
     
112. /****************************************8*16的点阵************************************/
     
113. const unsigned char F8X16[]=
     
114. {
     
115.   0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 0
     
116.   0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 1
     
117.   0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 2
     
118.   0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 3
     
119.   0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 4
     
120.   0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 5
     
121.   0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 6
     
122.   0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 7
     
123.   0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 8
     
124.   0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 9
     
125.   0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 10
     
126.   0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 11
     
127.   0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 12
     
128.   0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 13
     
129.   0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 14
     
130.   0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 15
     
131.   0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 16
     
132.   0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 17
     
133.   0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 18
     
134.   0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 19
     
135.   0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 20
     
136.   0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 21
     
137.   0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 22
     
138.   0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 23
     
139.   0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 24
     
140.   0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 25
     
141.   0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 26
     
142.   0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 27
     
143.   0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 28
     
144.   0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 29
     
145.   0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 30
     
146.   0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 31
     
147.   0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//[url=home.php?mod=space&uid=5830]@[/url] 32
     
148.   0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 33
     
149.   0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 34
     
150.   0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 35
     
151.   0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 36
     
152.   0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 37
     
153.   0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 38
     
154.   0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 39
     
155.   0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 40
     
156.   0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 41
     
157.   0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 42
     
158.   0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 43
     
159.   0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 44
     
160.   0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 45
     
161.   0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 46
     
162.   0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 47
     
163.   0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 48
     
164.   0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 49
     
165.   0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 50
     
166.   0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 51
     
167.   0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 52
     
168.   0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 53
     
169.   0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 54
     
170.   0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 55
     
171.   0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 56
     
172.   0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 57
     
173.   0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 58
     
174.   0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 59
     
175.   0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 60
     
176.   0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 61
     
177.   0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 62
     
178.   0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 63
     
179.   0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 64
     
180.   0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 65
     
181.   0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 66
     
182.   0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 67
     
183.   0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 68
     
184.   0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 69
     
185.   0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 70
     
186.   0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 71
     
187.   0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 72
     
188.   0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 73
     
189.   0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 74
     
190.   0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 75
     
191.   0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 76
     
192.   0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 77
     
193.   0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 78
     
194.   0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 79
     
195.   0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 80
     
196.   0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 81
     
197.   0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 82
     
198.   0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 83
     
199.   0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 84
     
200.   0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 85
     
201.   0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 86
     
202.   0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 87
     
203.   0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 88
     
204.   0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 89
     
205.   0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 90
     
206.   0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 91
     
207.   0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 92
     
208.   0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 93
     
209.   0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
     
210. };
     
211. char Hzk[][32]={
     
212. // 瑞(0) 萨(1) 年(2) 月(3) 日(4) 电(5)子(6)
     
213. 
     
214. {0x84,0x84,0xFC,0x84,0x84,0x40,0x5E,0x50,0x50,0x50,0xDF,0x50,0x50,0x50,0x5E,0x00},
     
215. {0x10,0x30,0x1F,0x08,0x08,0x00,0xFE,0x02,0x02,0x7F,0x02,0x7E,0x02,0x82,0xFE,0x00},/*"瑞",0*/
     
216. /* (16 X 16 , 宋体 )*/
     
217. 
     
218. {0x04,0xE4,0x24,0x24,0xA4,0x6F,0x04,0x24,0x64,0xAF,0x34,0xA4,0x64,0x24,0x04,0x00},
     
219. {0x00,0xFF,0x00,0x11,0x22,0x9C,0x40,0x3F,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x00},/*"萨",1*/
     
220. /* (16 X 16 , 宋体 )*/
     
221. 
     
222. {0x00,0x20,0x18,0xC7,0x44,0x44,0x44,0x44,0xFC,0x44,0x44,0x44,0x44,0x04,0x00,0x00},
     
223. {0x04,0x04,0x04,0x07,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x04,0x04,0x00},/*"年",2*/
     
224. /* (16 X 16 , 宋体 )*/
     
225. 
     
226. {0x00,0x00,0x00,0xFE,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0xFE,0x00,0x00,0x00},
     
227. {0x80,0x40,0x30,0x0F,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x82,0x7F,0x00,0x00,0x00},/*"月",3*/
     
228. /* (16 X 16 , 宋体 )*/
     
229. 
     
230. {0x00,0x00,0x00,0xFE,0x82,0x82,0x82,0x82,0x82,0x82,0x82,0xFE,0x00,0x00,0x00,0x00},
     
231. {0x00,0x00,0x00,0xFF,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0xFF,0x00,0x00,0x00,0x00},/*"日",4*/
     
232. /* (16 X 16 , 宋体 )*/
     
233. 
     
234. {0x00,0x00,0xF8,0x88,0x88,0x88,0x88,0xFF,0x88,0x88,0x88,0x88,0xF8,0x00,0x00,0x00},
     
235. {0x00,0x00,0x1F,0x08,0x08,0x08,0x08,0x7F,0x88,0x88,0x88,0x88,0x9F,0x80,0xF0,0x00},/*"电",5*/
     
236. /* (16 X 16 , 宋体 )*/
     
237. 
     
238. {0x80,0x82,0x82,0x82,0x82,0x82,0x82,0xE2,0xA2,0x92,0x8A,0x86,0x82,0x80,0x80,0x00},
     
239. {0x00,0x00,0x00,0x00,0x00,0x40,0x80,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"子",6*
     
240. /* (16 X 16 , 宋体 )*/
     
241. 
     
242. };
     
243. 
     
244. #endif /* OLEDFONT_H_ */

复制代码

1. 
   
2. //--------------------------------------------------------------------------------------------------
   
3. // 函数头文件    |   0   |   1   |   2   |   3   |   4   |   5   |   6   |   7   |   8   |   9
   
4. //--------------------------------------------------------------------------------------------------
   
5. #include "hal_data.h"
   
6. #include "oled.h"
   
7. #include "bmp.h"
   
8. #include "bsp_debug_uart.h"
   
9. #include "bsp_led.h"
   
10. FSP_CPP_HEADER
    
11. void R_BSP_WarmStart(bsp_warm_start_event_t event);
    
12. FSP_CPP_FOOTER
    
13. 
    
14. /* Callback function */
    
15. i2c_master_event_t i2c_event = I2C_MASTER_EVENT_ABORTED;
    
16. void sci_i2c_master_callback(i2c_master_callback_args_t *p_args)
    
17. {
    
18.     i2c_event = I2C_MASTER_EVENT_ABORTED;
    
19.     if (NULL != p_args)
    
20.     {
    
21.         /* capture callback event for validating the i2c transfer event*/
    
22.         i2c_event = p_args->event;
    
23.     }
    
24. 
    
25. }
    
26. 
    
27. fsp_err_t err = FSP_SUCCESS;
    
28. uint32_t  timeout_ms = 1000;
    
29. 
    
30. 
    
31. void Hardware_init(void)
    
32. {
    
33. 
    
34. 
    
35.             Debug_UART4_Init(); // SCI4 UART 调试串口初始化
    
36.             printf("Debug-UART4-Init OK \r\n");
    
37.             LED_Init();
    
38.             printf("LED_Init    OK \r\n");
    
39.             printf("IIC-Config  OK \r\n");
    
40.             /* Initialize the I2C module */
    
41.             err = R_SCI_I2C_Open(&g_i2c5_ctrl, &g_i2c5_cfg);
    
42.             /* Handle any errors. This function should be defined by the user. */
    
43.             assert(FSP_SUCCESS == err);
    
44.             printf("IIC-Config OK \r\n");
    
45.             OLED_Init();            //初始化OLED
    
46.             OLED_Clear();
    
47.             printf("oled-Init OK \r\n");
    
48. }
    
49. //==================================================================================================
    
50. //  函数说明: 主函数入口
    
51. //  函数备注: hal_entry
    
52. //--------------------------------------------------------------------------------------------------
    
53. //  |   -   |   -   |   0   |   1   |   2   |   3   |   4   |   5   |   6   |   7   |   8   |   9
    
54. //==================================================================================================
    
55. 
    
56. /*******************************************************************************************************************//**
    
57. * main() is generated by the RA Configuration editor and is used to generate threads if an RTOS is used.  This function
    
58. * is called by main() when no RTOS is used.
    
59. **********************************************************************************************************************/
    
60. void hal_entry(void)
    
61. {
    
62.     /* TODO: add your own code here */
    
63. 
    
64.           Hardware_init();
    
65.           printf("RA6M5-Board-Init OK \r\n");
    
66. 
    
67. 
    
68.           while(1)
    
69.           {
    
70.                 LED1_ON; // LED1亮
    
71.                 LED2_ON; // LED2亮
    
72.                 LED3_ON; // LED3亮
    
73.                 R_BSP_SoftwareDelay(500, BSP_DELAY_UNITS_MILLISECONDS); //延时1秒
    
74.                 LED1_OFF; // LED1灭
    
75.                 LED2_OFF; // LED2灭
    
76.                 LED3_OFF; // LED3灭
    
77.                 R_BSP_SoftwareDelay(500, BSP_DELAY_UNITS_MILLISECONDS); //延时1秒
    
78.   
    
79. 
    
80.                  printf("oled-Init OK \r\n");
    
81.                  OLED_ShowCHinese(0,0,0);//记
    
82.                  OLED_ShowCHinese(16,0,1);//帖
    
83.                  OLED_ShowCHinese(32,0,5);//电
    
84.                  OLED_ShowCHinese(48,0,6);//子
    
85.                  OLED_ShowString(60,0,"Renesas",16);
    
86.                  OLED_ShowNum(0,2,2023,4,16);//显示ASCII字符的码值
    
87.                  OLED_ShowCHinese(32,2,2);//中文字->年
    
88.                  OLED_ShowNum(48,2,5,2,16);//显示ASCII字符的码值
    
89.                  OLED_ShowCHinese(64,2,3);//中文字->月
    
90.                  OLED_ShowNum(80,2,12,2,16);//显示ASCII字符的码值
    
91.                  OLED_ShowCHinese(96,2,4);//中文字->日
    
92.                  OLED_ShowString(0,4,"By2023-CoderEnd",12);
    
93.                  OLED_ShowString(0,5,"Embedfire-Board",12);
    
94.                  OLED_ShowString(0,6,"R7FA6M5BH3CFC",16);
    
95. 
    
96.                   R_BSP_SoftwareDelay(4, BSP_DELAY_UNITS_SECONDS); //延时1秒
    
97.                   OLED_Clear();
    
98.                   OLED_DrawBMP(0,0,64,8,BMP1);
    
99.                   R_BSP_SoftwareDelay(4, BSP_DELAY_UNITS_SECONDS); //延时1秒
    
100.                   OLED_Clear();
     
101. 
     
102.           }
     
103. 
     
104. 
     
105. 
     
106. #if BSP_TZ_SECURE_BUILD
     
107.     /* Enter non-secure code */
     
108.     R_BSP_NonSecureEnter();
     
109. #endif
     
110. }
     
111. 
     
112. /*******************************************************************************************************************//**
     
113. * This function is called at various points during the startup process.  This implementation uses the event that is
     
114. * called right before main() to set up the pins.
     
115. *
     
116. * @param[in]  event    Where at in the start up process the code is currently at
     
117. **********************************************************************************************************************/
     
118. void R_BSP_WarmStart(bsp_warm_start_event_t event)
     
119. {
     
120.     if (BSP_WARM_START_RESET == event)
     
121.     {
     
122. #if BSP_FEATURE_FLASH_LP_VERSION != 0
     
123. 
     
124.         /* Enable reading from data flash. */
     
125.         R_FACI_LP->DFLCTL = 1U;
     
126. 
     
127.         /* Would normally have to wait tDSTOP(6us) for data flash recovery. Placing the enable here, before clock and
     
128.          * C runtime initialization, should negate the need for a delay since the initialization will typically take more than 6us. */
     
129. #endif
     
130.     }
     
131. 
     
132.     if (BSP_WARM_START_POST_C == event)
     
133.     {
     
134.         /* C runtime environment and system clocks are setup. */
     
135. 
     
136.         /* Configure pins. */
     
137.         R_IOPORT_Open (&g_ioport_ctrl, g_ioport.p_cfg);
     
138.     }
     
139. }
     
140. 
     
141. #if BSP_TZ_SECURE_BUILD
     
142. 
     
143. BSP_CMSE_NONSECURE_ENTRY void template_nonsecure_callable ();
     
144. 
     
145. /* Trustzone Secure Projects require at least one nonsecure callable function in order to build (Remove this if it is not required to build). */
     
146. BSP_CMSE_NONSECURE_ENTRY void template_nonsecure_callable ()
     
147. {
     
148. 
     
149. }
     
150. #endif

复制代码

开发板测试效果

WishWish

顶